NHTSA owner reports · September 18, 2026 snapshot.
Electrical System complaints
43 reportsClear category filterMileage unknown · Sep 12, 2025
Electrical SystemService Brakes
My 2008 Toyota Highlander Hybrid is having severe issues with the ABS system. Toyota is reporting that it needs an ABS actuator and ABS pump replacements. These were a part of Toyota's previous Customer Support Program, but the program expired before I owned the vehicle. That is EXTREMELY dangerous and the issue with the ABS sys…
Read full complaint
My 2008 Toyota Highlander Hybrid is having severe issues with the ABS system. Toyota is reporting that it needs an ABS actuator and ABS pump replacements. These were a part of Toyota's previous Customer Support Program, but the program expired before I owned the vehicle. That is EXTREMELY dangerous and the issue with the ABS system should be considered a Safety Recall that is ALWAYS available to Toyota customers to rectify and paid for by Toyota. It is a BRAKING ISSUE. It is not just brake pads, or normal wear and tear. This is a known issue and regardless of the timeline, Toyota should absolutely pay for the repair.
NHTSA ODI #11686896
Mileage unknown · Aug 17, 2025
Electrical System
The Intelligent power module failed on the vehicle. I read this is common for my vehicle however there is no recall matching my VIN. Vehicle was purchased out of state one year ago. We took the vehicle to a Toyota dealership who suggested I inquire about the issue because it’s possible this VIN should have been included.
NHTSA ODI #11681187
271,890 miles · Aug 14, 2025
Electrical System
Odometer Fraud. The contact purchased a 2008 Toyota Highlander. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 123,399, and at the time of registration, it was discovered tha…
Read full complaint
Odometer Fraud. The contact purchased a 2008 Toyota Highlander. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 123,399, and at the time of registration, it was discovered that the mileage was 271,890.
NHTSA ODI #11680713
Mileage unknown · Feb 27, 2024
Electrical SystemService Brakes
Myself, and many other 2008 Toyota Highlander Hybrid owners, have a vehicle code labeled C1391 "Leak in Accumulator" wherein the vehicles brake actuator and brake booster pump malfunction. The dash of my vehicle has the following indicators on; Check ABS, Check Brake System, Check VSC System, Yellow Master Warning Light, Red Bra…
Read full complaint
Myself, and many other 2008 Toyota Highlander Hybrid owners, have a vehicle code labeled C1391 "Leak in Accumulator" wherein the vehicles brake actuator and brake booster pump malfunction. The dash of my vehicle has the following indicators on; Check ABS, Check Brake System, Check VSC System, Yellow Master Warning Light, Red Brake System Light & Buzzer, Yellow ABS Warning Light, and Yellow Slip Indicator Light. This has been a significant cause of concern for me over the past two-three years since purchasing this vehicle. This is a known issue throughout the Toyota Highlander Hybrid community and the dealership is not upholding their previous recall which occurred in late 2019 and ended in 2020, after I had purchased the vehicle. The cost of repairs is upwards of $4,000 and Toyota has not given the proper opportunity for recall repairs to owners. This is a significant safety issue because if the brakes fail, a severe crash may injure myself or others. The problem has been reproduced by several other owners, dealerships, and independent service centers (this is a well known and common issue). This vehicle is available for inspection if requested. I plead that you please insist on Toyota reopening their recall to provide service to the owners of this vehicle, this is an issue with their manufacturing and not on the owners/operators. This problem occurred immediately after receiving scheduled maintenance to my vehicle from a certified Toyota Dealership, whom have quoted me the above cost for repairs and may have caused the issue in the first place.
NHTSA ODI #11574334
Mileage unknown · May 6, 2023
Air BagsElectrical System
Air bag lights continue to show. Vehicle had not been in any accidents. Seat warms do not work light comes on when you turn them on. Driver window will go up half way occasionally. Back wiper motor makes loud noise and doesn’t work anymore. Tire sensor also comes out.
NHTSA ODI #11520740
Mileage unknown · Mar 31, 2023
Electrical SystemSteeringVehicle Speed Control
My 2008 toyota highlander gas pedal must be lose.because I barley push the gas and it takes on fast.i was driving home on the highway and the truck just died .the battery dies I couldn't turn my wheel I could not press the break
NHTSA ODI #11514719
Mileage unknown · Jun 13, 2022
Electrical SystemUnknown Or Other
This vehicle has had ongoing issues with the O2 sensors not working, I have researched online for years and have read that there are several online forums of 2008 Highlander owners complaining of the same issue. The problem that I (we all) face with this, is that it constantly fails, never being able to know if there is an actua…
Read full complaint
This vehicle has had ongoing issues with the O2 sensors not working, I have researched online for years and have read that there are several online forums of 2008 Highlander owners complaining of the same issue. The problem that I (we all) face with this, is that it constantly fails, never being able to know if there is an actual issue becuase of the faulty sensors or wiring causing the sensors to go out. I am always frightened that something is wrong with the car and spent hundreds and continue to spend having my car checked. I am a single mom who lost my job at the beginning of the pandemic, I have two school aged kids. Having them in a car that I can not be sure we are safe in, is scary. The cost to replace the sensors as there are 3 that have been a constant pain of not working correctly is insane! It is going to be in upwards of $600 to repair! I absolutely can't afford that, being an unemployed single mother of two. Even when I was employed, living paycheck to paycheck to have to pay out almost a thousand dollars when from what I've read from others that replacing will still result in it failing again. So I have to drive around in a car that has all the sensor lights on, something really bad could happen to the car and since all the sensor lights remain on, I'll never know if something is wrong with the car- something bad could happen to me and my children while we are driving in the car. How can someone replace the sensors only for them to keep going out. This is a serious problem, I've dealt with this for years, only today did I learn that I could report this after receiving a recall letter from Toyota today regarding the paint on my car.
NHTSA ODI #11468963
Mileage unknown · Apr 5, 2022
Electrical SystemService BrakesCrash
ABS system failure for the second time after repair, cost $3400 to replace after causing complete loss of brakes. 4 years after incident same exact ABS warning and VCS system failure with message to immediately take vehicle to dealership. There is a class action lawsuit on other hybrid models but Toyota inspected and said it wou…
Read full complaint
ABS system failure for the second time after repair, cost $3400 to replace after causing complete loss of brakes. 4 years after incident same exact ABS warning and VCS system failure with message to immediately take vehicle to dealership. There is a class action lawsuit on other hybrid models but Toyota inspected and said it would cost another $3500 to fix because there is no recall on the part.
NHTSA ODI #11459644
151,000 miles · Sep 15, 2020
Electrical SystemEngineFuel/propulsion System
2008 HIGHLANDER HYBRID LIMITED CHECK ENGINE LIGHT CAME ON AND SHOWED CODE P0A1B - DRIVE MOTOR 'A' CONTROL MODULE, THE CODE WAS CLEARED MANUALLY AND THE CHECK ENGINE LIGHT WENT OFF, THE NEXT DAY THE LIGHT CAME BACK ON AFTER DRIVING ABOUT 3 MILES THEN PARKED. THE NEXT DAY THE LIGHT WENT OFF ON ITS OWN AS WE TOOK IT TO THE TOYOTA D…
Read full complaint
2008 HIGHLANDER HYBRID LIMITED CHECK ENGINE LIGHT CAME ON AND SHOWED CODE P0A1B - DRIVE MOTOR 'A' CONTROL MODULE, THE CODE WAS CLEARED MANUALLY AND THE CHECK ENGINE LIGHT WENT OFF, THE NEXT DAY THE LIGHT CAME BACK ON AFTER DRIVING ABOUT 3 MILES THEN PARKED. THE NEXT DAY THE LIGHT WENT OFF ON ITS OWN AS WE TOOK IT TO THE TOYOTA DEALERSHIP AND HAS NOT BEEN BACK ON SINCE DRIVING IT THERE AND BACK, THE DEALERSHIP SAID THEY DROVE AROUND A LITTLE AND THE LIGHT NEVER CAME ON, WE BROUGHT IT HOME AND HAVE DRIVEN ABOUT 7 MILES WITHOUT THE LIGHT COMING ON. ACCORDING TO THE LOCAL TOYOTA DEALERSHIP AND CORPORATE TOYOTA THERE ARE NO RECALLS FOR OUR VIN BUT IT IS SHOWING ALL SIGNS OF THE INVERTER ASSEMBLY RECALL THAT AFFECTED 235,000 VEHICLES IN THE RECALL. TOYOTA QUOTED THE REPAIR AT $9000+ AND EVEN THOUGH IT HAS THE SYMPTOMS OF THE RECALLED VEHICLES THEY WILL NOT FIX IT BECAUSE IT IS NOT ON THE RECALL LIST AND THERE IS NOTHING THEY CAN DO. THE REPAIR COST IS MORE THAN THE VALUE OF THE CAR.
NHTSA ODI #11355261
160,000 miles · Jul 12, 2020
Electrical SystemEngineFuel/propulsion System
HIGHLANDER HYBRID 2008 WE WERE DRIVING ON A COUNTRY BACK ROAD. IN IDAHO, WE HAD JUST STOPPED AT A STOP SIGN AND WENT TO DRIVE FORWARD AFTER GOING AROUND 100-200 METERS AND THE CAR LURCHED FORWARD WHILE I WAS DRIVING AND THEN THE SCREEN WITH ALL THE WARNINGS BEGAN GOING OFF. ALL OF THEM SAYING PULL OVER TOT THE SIDE OF THE ROA…
Read full complaint
HIGHLANDER HYBRID 2008 WE WERE DRIVING ON A COUNTRY BACK ROAD. IN IDAHO, WE HAD JUST STOPPED AT A STOP SIGN AND WENT TO DRIVE FORWARD AFTER GOING AROUND 100-200 METERS AND THE CAR LURCHED FORWARD WHILE I WAS DRIVING AND THEN THE SCREEN WITH ALL THE WARNINGS BEGAN GOING OFF. ALL OF THEM SAYING PULL OVER TOT THE SIDE OF THE ROAD AND THAT ALL THE SYSTEMS WERE FAILING. ALL THE WARNINGS SAID THINGS TO TAKE THE CAR TO DEALER. WE PULLED OVER TO THE SIDE OF THE ROAD AND THEN TRIED TO GET THE CAR TO MOVE FORWARD BY PUTTING IT IN DRIVE AND YOU COULD HEAR THE CAR TRYING TO DO SOMETHING BUT NOTHING HAPPENED. THE CAR DID TURN ON BUT THAT WAS IT.
NHTSA ODI #11338931
Official recalls
11Jun 2, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Consequence & remedy
Consequence: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Nov 19, 2014
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Consequence & remedy
Consequence: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Apr 21, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence & remedy
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Additional source detail variants (2)
Air Bags:side/window
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Air Bags
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Feb 3, 2010
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Jan 27, 2010
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2010 HIGHLANDER, MODEL YEAR 2009-2010 COROLLA, VENZA AND MATRIX PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT. THIS RECALL IS AN EXPANSION OF A CAMPAIGN OF 3.8 MILLION OTHER TOYOTA VEHICLES ANNOUNCED IN 2009 FOR THE SAME ISSUE (SEE 09V-388).
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: TOYOTA WILL MODIFY OR REPLACE THE ACCELERATOR PEDALS ON THE SUBJECT VEHICLES. FLOOR SURFACE MODIFICATIONS ARE ALSO BEING CONSIDERED AND WILL BE INCLUDED FOR ANY MODEL FOR WHICH IT IS DEEMED APPROPRIATE. INITIALLY, DEALERS WILL BE INSTRUCTED ON HOW TO RESHAPE THE ACCELERATOR PEDAL FOR THE REPAIR. AS REPLACEMENT PARTS WITH THE SAME SHAPE AS THE MODIFIED PEDAL BECOME AVAILABLE, THEY WILL BE MADE AVAILABLE TO THE DEALERS FOR THE REPAIR. CUSTOMERS WHO HAVE HAD THE PEDAL RESHAPE REMEDY COMPLETED WILL HAVE THE OPPORTUNITY TO RECEIVE A NEW PEDAL IF THEY DESIRE, AFTER REPLACEMENT PEDALS BECOME AVAILABLE. IN ADDITION, TOYOTA WILL REPLACE ANY TOYOTA ALL-WEATHER FLOOR MAT IN A SUBJECT VEHICLE WITH A NEWLY DESIGNED MAT, FREE OF CHARGE. FOR THOSE CUSTOMERS WHO HAVE THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT BUT DO NOT NEED OR WANT THE NEWLY DESIGNED ALL-WEATHER FLOOR MAT, TOYOTA WILL RECOVER THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT AND REIMBURSE ITS PRICE. THE SAFETY RECALL BEGAN MARCH 30, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Apr 18, 2008
TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.
Consequence & remedy
Consequence: HOWEVER, FOR THE TWO THIRD ROW DSP'S ON THESE VEHICLES, THE ALR MODE DEACTIVATES BEFORE THE WEBBING IS FULLY RETRACTED, SO THAT IT WILL NOT LOCK WHEN CERTAIN REAR-FACING CRS'S THAT HAVE A SHORT SEAT BELT ROUTING PATH ARE INSTALLED IN THE VEHICLE. THIS CAN ALLOW THE SEAT BELT WEBBING TO SPOOL OUT DURING NORMAL DRIVING MANEUVERS, WHICH COULD AFFECT THE STABILITY OF A CHILD RESTRAINT INSTALLED AT THOSE SEATING POSITIONS. AS SUCH, THIS COULD DISCOURAGE THE USE OF A CHILD RESTRAINT AND IN THE EVENT OF A CRASH, THE CHILD MAY NOT BE ADEQUATELY PROTECTED POSSIBLY RESULTING IN INJURY.
Remedy: DEALERS WILL INSTALL A NEWLY DESIGNED SEAT BELT COMPONENT FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 18, 2008. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Illustration