NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
32 reportsClear category filterMileage unknown · May 30, 2026
Forward Collision AvoidanceService BrakesVehicle Speed Control
[XXX], [XXX] PM. 2024 Toyota Tundra Hybrid (i-FORCE MAX, V35A engine), 36k miles, original owner. Clear, dry pavement, evening daylight. Exiting [XXX] westbound at [XXX] , I merged into the far right lane at the second light for a right turn. A vehicle was stopped ahead at the light. Traveling 15-20 mph, I applied the brake …
Read full complaint
[XXX], [XXX] PM. 2024 Toyota Tundra Hybrid (i-FORCE MAX, V35A engine), 36k miles, original owner. Clear, dry pavement, evening daylight. Exiting [XXX] westbound at [XXX] , I merged into the far right lane at the second light for a right turn. A vehicle was stopped ahead at the light. Traveling 15-20 mph, I applied the brake for controlled deceleration. Right foot squarely on brake, not touching accelerator. Vehicle did not decelerate as expected. For 3-4 seconds the brake felt unresponsive — pedal felt soft and loose, lacking normal firmness. I pressed the brake fully to the floor. A dashboard warning appeared: “gas and brake pedals are being pressed simultaneously.” I was not, and had not been, touching the accelerator. I then heard engine RPM increase audibly, consistent with an acceleration command, while my foot remained fully on the brake. I felt forward thrust working against my braking. The warning cleared and brakes engaged. Vehicle stopped approximately half a car length from the vehicle ahead, narrowly avoiding rear-end collision. Automatic Emergency Braking did NOT engage despite conditions clearly meeting its criteria — stationary vehicle directly ahead, my vehicle approaching at 15-20 mph with no observable deceleration for 3-4 seconds. No collision warning sounded; no auto-braking intervened. Notably, this same AEB has previously engaged falsely in benign situations (e.g., backing near low vegetation), suggesting reliability/calibration issues. Prior manufacturer notice: On [XXX] at 15,412 miles, I reported to Camelback Toyota, Phoenix (RO #[XXX], on file): “vehicle lurches forward going from reverse to drive (now more consistent)” — dispositioned by tech 10210 as “vehicle is operating to spec,” no diagnosis performed. Same RO documented “rattling in neutral/at stop” — dispositioned “unable to duplicate.” Toyota was on notice of throttle-response symptoms 21 months before this safety event. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11741033
Mileage unknown · May 26, 2026
Back Over PreventionForward Collision AvoidanceVehicle Speed Control
THROTTLE BODY WAS REPLACED, NO DEALER ADVICE TO REPLACE DRIVING DOWN THE ROAD ALL OF A SUDDEN MY VEHICLE WENT FROM HIGHWAY SPEEDS TO LIMP MODE ON THE MIDDLE OF THE HIGHWAY AND A WHOLE BUNCH OF WARNINGS CAME ON SECONDARY BRAKE SYSTEM FAILURE, HYBRID CONTROL FAILURE , STOPED ON THE SIDE OF ROAD TRUCK STALLED THEN RESTARTED NORMAL…
Read full complaint
THROTTLE BODY WAS REPLACED, NO DEALER ADVICE TO REPLACE DRIVING DOWN THE ROAD ALL OF A SUDDEN MY VEHICLE WENT FROM HIGHWAY SPEEDS TO LIMP MODE ON THE MIDDLE OF THE HIGHWAY AND A WHOLE BUNCH OF WARNINGS CAME ON SECONDARY BRAKE SYSTEM FAILURE, HYBRID CONTROL FAILURE , STOPED ON THE SIDE OF ROAD TRUCK STALLED THEN RESTARTED NORMAL THEN ALL WARNINGS CAME BACK AND BACK TO LIMP MODE, PROBLEM COMFIRMED BY DEALER IN EL PASO ALMOST 300 MILES AWAY FROM HOME, NOT SURE WHO THE DEALER SHOWED TO , AND NO PRIOR WARNINGS AT ALL BEFORE THIS HAPPEND AT 51K MILES ON MY 2024 TOYOTA TUNDRA.
NHTSA ODI #11740238
Mileage unknown · Apr 21, 2026
EnginePower TrainVehicle Speed Control
approaching a round about at a slow rate of speed, prior to entering I noticed there was time to safely enter the round about ahead of a car also entering the roundabout from another direction. I pushed the accelerator pedal to about 30% at the time I choose to enter the traffic circle and attempted to enter. The truck did nothi…
Read full complaint
approaching a round about at a slow rate of speed, prior to entering I noticed there was time to safely enter the round about ahead of a car also entering the roundabout from another direction. I pushed the accelerator pedal to about 30% at the time I choose to enter the traffic circle and attempted to enter. The truck did nothing in response except keep rolling forward due to the momentum I already had while approaching the round about / traffic circle. After about 2 seconds, I pressed the pedal to about 70%. This still did nothing for about another 1 second, before the truck accelerated as if I had pressed the pedal to 70% from a stop. fast acceleration into the round about which caused a narrow miss between me and the original car mentioned that was also entering the traffic circle.
NHTSA ODI #11732794
Mileage unknown · Apr 20, 2026
Power TrainVehicle Speed Control
Very commonly when the truck is “cold” after sitting overnight, the truck fails to accelerate from a stop while pushing the accelerator pedal down gradually (such as when leaving a stop sign at an intersection. This lack of acceleration makes me feel a loss of control as I cannot get the truck to accelerate. For example, driving…
Read full complaint
Very commonly when the truck is “cold” after sitting overnight, the truck fails to accelerate from a stop while pushing the accelerator pedal down gradually (such as when leaving a stop sign at an intersection. This lack of acceleration makes me feel a loss of control as I cannot get the truck to accelerate. For example, driving out of my neighborhood into oncoming road traffic I feel as if the truck doesn’t sense my pedal input. The truck just “floats” for at least a few seconds before the pedal reaches a point where the truck recognizes the input and activates acceleration. I can see this situation causing a safety hazard such as when trying to gain speed from a stop. The dealerships says it’s a non-issue and normal for a turbo-charged engine. I have owned cars with turbo-charged engines and have never experienced this bad of lag before. I don’t feel this is normal. My truck currently has no engine issues and is maintained routinely.
NHTSA ODI #11732583
Mileage unknown · Feb 17, 2026
Power TrainVehicle Speed Control
I am an automotive engineer. I have been involved with vehicle development programs in the disabled vehicle conversion community for over two decades and have numerous patents in that space. I have been involved with vehicle testing and calibration as well. My vehicle demonstrates a SIGNIFICANT HESITATION when the acceler…
Read full complaint
I am an automotive engineer. I have been involved with vehicle development programs in the disabled vehicle conversion community for over two decades and have numerous patents in that space. I have been involved with vehicle testing and calibration as well. My vehicle demonstrates a SIGNIFICANT HESITATION when the accelerator is pressed that is not consistent. I live in a roundabout dense location where timing an entry into a roundabout is easy using a normal vehicle. The 1 to 2 second hesitation where there is throttle input and no action at all from the vehicle (engine does not rev, no motive power observed) is very dangerous. I took this up with Toyota and my vehicle was checked out and "learning transmission" memory was wiped clean with me being the only driver was the remedy. The issue got better for a short time but is back and this morning I pulled out thinking there was plenty of time in front of a bus a good distance away and the lack of motive power for a full second or two resulted in a near miss. This vehicle has about 20,000 miles and was purchased by me new. There are NO WARNING LAMPS, and no DTCs thrown when this happens. I have seen several videos where people cite the same experience and a website where there is a class action lawsuit in place regarding this issue. This is completely separate from the engine recall issue. I feel as though this issue is a significant safety risk.
NHTSA ODI #11718438
Mileage unknown · Feb 8, 2026
EngineFuel/propulsion SystemVehicle Speed Control
The engine repair was a short block only, even thoe the main bearings spun and sent debis threw the engine. #1 rod went as well. Apon recieving the truck back, with in 200 miles, I've had the same hesitation with the engines as I had just before the first engine failed. Took it by the dealer and no issues found. oil preasure sta…
Read full complaint
The engine repair was a short block only, even thoe the main bearings spun and sent debis threw the engine. #1 rod went as well. Apon recieving the truck back, with in 200 miles, I've had the same hesitation with the engines as I had just before the first engine failed. Took it by the dealer and no issues found. oil preasure stays up and temp normal. I've had many issue with throtle lag sence day one. The milage has stayed in the low 11 gpm when before i would get on average 14 to 16. Dealer stated toyota would make it right if the engine fails again. Very unhappy with Toyota as I feel they are just kicking the can down the road.
NHTSA ODI #11716527
Mileage unknown · Jan 16, 2026
Vehicle Speed Control
After a complete stop vehicle acceleration lags when pressing accelerator.
NHTSA ODI #11711563
Mileage unknown · Jan 16, 2026
Power TrainVehicle Speed Control
When at a complete stop, going to pull out, or continue driving, there is a noticable lag to the acceleration. It sometimes does nothing for a few seconds before acceleration. If backing up, then switching to drive,.there is a delay and or a small jerk motion before the vehicle accelerates. This has caused issues when pulling…
Read full complaint
When at a complete stop, going to pull out, or continue driving, there is a noticable lag to the acceleration. It sometimes does nothing for a few seconds before acceleration. If backing up, then switching to drive,.there is a delay and or a small jerk motion before the vehicle accelerates. This has caused issues when pulling out and vehicles are coming at normal speeds with plenty of time to pull out. The delay has almost caused several accidents.
NHTSA ODI #11711335
Mileage unknown · Jan 12, 2026
Vehicle Speed Control
When pulling out turning left across a busy street, my vehicle did not accelerate when I pressed the gas pedal for approximately one second. While only a short time, this was enough time to roll into the middle of traffic, but not get out of the way. This throttle hesitation/delay happened twice more in the same trip.
NHTSA ODI #11710532
Mileage unknown · Dec 24, 2025
Vehicle Speed Control
The vehicle experiences throttle lag from stop or when rapidly accelerating from one speed to another(passing on highway or merging on interstate). Pushing on the gas pedal does not receive an immediate response from the engine. Issue comes up when accelerating from a stop sign or merging/overtaking.
NHTSA ODI #11706929
Official recalls
10May 20, 2026
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2024 Tundra vehicles equipped with a V35A engine. Debris from the manufacturing process may contaminate the engine and cause a main bearing to fail, which can result in an engine stall and loss of drive power.
Consequence & remedy
Consequence: A loss of drive power increases the risk of a crash.
Remedy: Dealers will perform an inspection on the #1 main bearing using vehicle inspection software and drive data, and if necessary, replace the engine. Repairs will be performed free of charge. Interim letters notifying owners of the safety risk were mailed July 23, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's numbers for this recall are 25TB14 and 25TA14. This recall expands previous NHTSA recall numbers 24V381 and 25V767.
Mar 24, 2026
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2024-2025 Toyota Tundra, Tacoma Hybrid, Tacoma, RAV4 Hybrid, Land Cruiser Hybrid, Lexus GX550, 2024-2026 Tundra Hybrid, 2025 Sequoia Hybrid, Crown Signia, Grand Highlander, Lexus TX500 Hybrid, Lexus NX350 Hybrid, 2025-2026 Grand Highlander Hybrid, and Lexus TX350 vehicles. The load carrying capacity modification label may display inaccurate added weight values. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: A vehicle with an incorrect maximum capacity weight value may be overloaded, which can increase the risk of a crash.
Remedy: Dealers will replace the load carrying capacity modification label, free of charge. Owner letters were mailed May 26, 2026. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's numbers for this recall are 26LB04, 26LA04, 26TB07, and 26TA07.
Jan 23, 2026
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2024-2025 Toyota Tundra and Tundra Hybrid vehicles equipped with a Panoramic View Monitor (PVM) system. The rearview camera image may not display when the vehicle is placed in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview camera image that does not display reduces the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: Dealers will update the parking assist ECU software, free of charge. Owner notification letters were mailed March 23, 2026. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's numbers for this recall are 26TB02 and 26TA02.
Nov 6, 2025
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2024 Toyota Tundra, Lexus LX, and 2024 Lexus GX vehicles equipped with a V35A engine. Debris from the manufacturing process may contaminate the engine and cause the main bearings to fail, which can result in an engine stall and loss of drive power.
Consequence & remedy
Consequence: A loss of drive power increases the risk of a crash.
Remedy: Dealers will perform an inspection on the #1 main bearing using vehicle inspection software and drive data, and if necessary, replace the engine. Repairs will be performed free of charge. Owner letters were mailed August 28, 2026. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's numbers for this recall are 25TB14 and 25TA14. Lexus' numbers for this recall are 25LB07 and 25LA07. This recall expands previous NHTSA recall number 24V381.
Oct 1, 2025
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2025 Tundra, Tundra Hybrid, and 2023-2025 Sequoia Hybrid vehicles. A software error may cause the rearview image not to display when the vehicle is placed in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that does not display reduces the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: Dealers will update the multimedia display software, free of charge. Owner notification letters were mailed November 19, 2025. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's numbers for this recall are 25TB10 and 25TA10.
May 15, 2025
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2025 Toyota Tundra and Tundra Hybrid vehicles. Moisture may enter the reverse light assemblies and cause a light failure.
Consequence & remedy
Consequence: Reverse light failure may reduce visibility, and not alert pedestrians and other drivers that the vehicle is backing up, increasing the risk of a crash.
Remedy: Dealers will replace both reverse light assemblies and repair the wire harnesses as necessary, free of charge. Owner letters were mailed May 23, 2026. This is a phased recall. Owners may contact Toyota's customer service at 1-800-331-4331.Toyota's numbers for this recall are 24TB06 and 24TA06.
Oct 15, 2024
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2024 Sequoia Hybrid, Tundra and Tundra Hybrid vehicles. The passenger-side front and rear tires may have inner sidewall damage, which can cause a sudden loss of tire pressure.
Consequence & remedy
Consequence: A sudden loss of tire pressure can result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the tires as necessary, free of charge. Owner notification letters were mailed December 5, 2024. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is 24TA12.
Jul 23, 2024
Gulf States Toyota, Inc. (GST) is recalling certain Toyota 2023 GR Supra, 2024 4 Runner, Corolla, Grand Highlander, Grand Highlander Hybrid, Land Cruiser Hybrid, Tacoma, Tacoma Hybrid, 2023-2024 BZ4X, Corolla Cross Hybrid, GR Corolla, GR86, Highlander, Highlander Hybrid, Prius, Prius Prime, Sequoia Hybrid, Tundra, Tundra Hybrid, Venza Hybrid, 2023-2025 Crown, and 2025 Camry Hybrid vehicles equipped with GST accessories. The load carrying capacity modification label may display inaccurate added weight values. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: A vehicle with an incorrect maximum capacity weight value may be overloaded, which can increase the risk of a crash.
Remedy: GST will mail new labels to owners, free of charge. Owner notification letters were mailed September 16, 2024. Owners may contact GST customer service at 1-800-444-1074. GST's number for this recall is 24R2.
Feb 21, 2024
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2024 Tundra, Tundra Hybrid, Lexus LX600, and 2023-2024 Sequoia Hybrid vehicles. Unexpected vehicle movement may occur when the vehicle is in neutral and the brakes are not applied.
Consequence & remedy
Consequence: Unexpected vehicle movement can increase the risk of a crash.
Remedy: Dealers will update the transmission control ECU software, free of charge. Owner notification letters were mailed April 8, 2024. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 24TA02 and 24LA02.
Nov 9, 2023
Southeast Toyota Distributors, LLC (SET) is recalling certain 2022-2024 Toyota Tundra vehicles. The load carrying capacity modification label states the incorrect load carrying capacity, which can result in an overloaded vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An overloaded vehicle increases the risk of a crash.
Remedy: SET will mail a new modified label, free of charge. Owner notification letters were mailed December 18, 2023. Owners may contact SET's customer service at 1-866-405-4226. SET's number for this recall is SET23B.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗